Skip to main content
Home Educational Resources Inhalers Striverdi® Respimat®
Striverdi® Respimat®

Striverdi® Respimat®

Generic Name: Olodaterol

Links

Striverdi® Respimat®

Instructions for use

  1. Wash and dry your hands well.
  2. Hold the inhaler with the yellow cap closed.
  3. Press the safety catch on the side of the inhaler and pull off the clear base. (Do not touch the sharp piercing tool in the inside of the base.)
  4. Write the discard date on the label – three months from today.
  5. Take the silver cartridge out of the box.
  6. Insert the narrow end of the cartridge into the inhaler and push the cartridge against a firm surface to ensure proper insertion. A little bit of the cartridge (1/8 inch) will stick out of the bottom of the inhaler.
  7. Put the clear base back on the inhaler.
  8. Do not take the inhaler apart again after completing these steps.

Prime the inhaler before first use by following steps 9 to12.

  1. Hold the inhaler with the yellow cap closed and pointed up.
  2. Turn the clear base in the direction of the arrows on the label until you hear a click (half turn).
  3. Open the yellow cap and point the inhaler down. Push the dose release button, then close the cap.
  4. Repeat steps 9 to11 until you see a white spray coming from the inhaler.
  5. After you see the white spray, repeat steps 9-11 three more times. The inhaler is now ready for use.

Use the inhaler*

  1. Wash and dry your hands well.
  2. Sit up straight or stand up.
  3. Hold the inhaler with the yellow cap closed and pointed up.
  4. Turn the clear base in the direction of the arrows on the label until you hear a click (half turn).
  5. Open the yellow cap.
  6. Exhale fully out through mouth. Hold the inhaler so inhaler is pointed at the back of your throat.
  7. Place the mouthpiece between your lips. Make sure that your tongue is flat under the mouthpiece and does not block the opening.
  8. Seal your lips around the mouthpiece.
  9. Push the dose release button as you begin to slowly take in a deep breath through your mouth for as long as you can.
  10. Hold your breath for 10 seconds. If you cannot hold your breath for 10 seconds, then hold your breath for as long as possible.
  11. Repeat steps 6-10 to get the full dose of medicine (2 puffs equal one dose.)
  12. Close the cap after each use. Store in a cool dry place.

*If you have not used the inhaler for three or more days, follow priming steps 9 to11 for one spray. If you have not used your inhaler for more than 21 days, re-prime the inhaler using steps 9 to 13.

Key product details

Medication Class and Use

  • Long-acting bronchodilator (maintenance inhaler, or LABA): Works to relax the muscles that tighten around the airway and makes breathing easier. This medicine takes longer to start working than the short-acting bronchodilator, but works for a longer time. Do not use with other LABA containing medications.
  • Use this inhaler every day to prevent symptoms, even when feeling well.
  • Do not use for fast relief.

Dosing

  • Usual COPD dosing: 2 inhalations once daily
  • Not approved for use in asthma
  • Each inhaler contains 30 doses (2 puffs =1 dose)

Assembly/Priming

See extensive detailed instructions

Refill

  • Inhaler is empty when dose counter reads 0. Dose counter turns red at dose 7 to remind getting a refill.

This site does not endorse or recommend any individual medication and does not accept funding or advertising from drug manufacturers. Our intent is to share information about medication use so that you get the most benefit from your medicine.

The information provided is educational purposes only. It should not be used as a substitute for professional medical advice, diagnosis or treatment.

Copyright @2023 Fairview Physician Associates. All rights reserved.